|
|
|
|
ETI Part Number: ETI0001-1237
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| AC OUTPUT | |
| Output voltage: | 120 VAC true sinewave standard, others optional |
| Output rating: UPS | 2000 VA standard in 3U chassis 0.65-0.75 pf std, optional configurations to 24,000 VA |
| Non-linear load capacity: | Up to 100% non-linear load capability w/o derating |
| Output voltage regulation: UPS | ± 3.0% static regulation of nominal ± 4.0% dynamic (0 to 50% load step) |
| Overload surge capacity: | 110% for 10 minutes; 125% for 30 seconds |
| Harmonic distortion: | Less than 5.0% into 100% non-linear load |
| Output frequency: UPS | 60 Hz ± 1.0% independent of input frequency 50, 400 or 1000 Hz output available as an option |
| Operational status | Status, load and battery LEDs, w/contacts RS-232 asynchronous serial status COM port Adjustable level,+90 dB audible alarm w/on/off |
| AC INPUT | |
| Input voltage selection: | Nominal 115 VAC or 230 VAC via selection switch (S6) |
| Input voltage tolerance: UPS | 85-135 VAC or 170-270 @ full load without using battery, to 70 VAC @ 75% load |
| Input frequency: | From 46 Hz to 70 Hz standard, optional to 440 Hz |
| Input power factor: | Better than 99% typically |
| Input/output isolation: | 2000 VA, >120 dB common mode, <1.0 mA leakage |
| Input transient suppression: | Complies with IEEE 587 and UL 1449 |
| Input control/protection: | Guarded 2 pole switch (S1) w/fuse (F2) |
| Input power connection: | MS 3102A-22-2P, 3 pin, locking |
| INTERNAL BATTERY | |
| Battery type: | Maintenance free immobilized electrolyte, Flame retardant materials (Oxygen Index 28+) See ETI0001-1237AA for a new version with hot swappable battery module |
| Battery life: | Rated for continuous service life of 5 years |
| DC protection: | Front panel mounted fuse standard, breaker optional |
| Battery time: | 15+ minutes @ 100% load, 30+ minutes @ 50% |
| Battery recharge: | Recharged to nominal in <8 hours |
| DISTRIBUTION PANEL | |
| Output circuits: | One output standard, optional configurations |
| Output control: | Guarded 3 pole switch (S5) |
| Output receptacles: | MS 3102A-24-10S, 7 pin locking, other options |
| MECHANICAL | |
| Dimensions ( H x D x W ): | 5.25 (3U) x 28.0 x 19.0 in (133 x 711 x 483 mm) |
| Rack Slide Mount Patterns: | Actron/Jonathan slide pattern, others optional |
| Rack rear alignment pins: | (2) shock isolation/alignment pin/socket sets |
| Alternate Mounting Options: | Table, Wall, Floor, Portable, Horizontal/Vertical |
| Unit weight: | 155 lb. (70 kg) with lift handles front |
| Audible noise: | Less than 47 dB @ 5.0 ft., ANSI "A" scale |
| Cooling type: | High capacity, negative pressure, forced air |
| Cooling air direction: | Front intake, exhaust to rear, others optional |
| Air intake filter: | Washable metal filter media, others optional |
| ENVIRONMENTAL | |
| Storage temperature: | -40° to 158° F ambient (-40° to 70° C) with fully charged batteries |
| Operating temperature: | -4° to 131° F ambient ( -20° to 55° C), lower/ higher optional |
| Operating humidity: | 0 to 95% relative humidity (non-condensing) |
| Storage elevation: | Up to 40,000 ft (12,192 m) |
| Operating elevation: | Up to 15,000 ft (4,572 m), higher optional |
| STANDARDS | |
| United States: | Meets UL-1778 standard for UPS
equipment, MIL STDs 167-1, 454, 810, 901D Grade A, 1399-300A & 2000 |
| Canada: | CSA C22.2 No. 107 UPS safety requirements |
| EMI Protection: | EMI/RFI FCC Part 15, Class A; EN55022; MIL STD 461 standard |
| OPTIONAL ACCESSORIES | |
| Autoranging International Input, Emergency Power Off, Elapsed Time Meter, Cold Start, Alternate I/O Configurations, Dual Source Input, Battery Expansion, Batteryless Operation, Battery Charger/Conditioner, Power Distribution Units, Software Interface, 10BaseT Ethernet SNMP/HTTP port, Transport Cases | |
This page was last modified on:
April 12, 2012
Request Information
